Primer Application Guide

Primer Application Guide
Name
Description
Standard
1
Primer
General Service Bis A Epoxy
Primer
901
General Service Bis F Epoxy
Primer- Better Chemical
Resistance Than Standard
Primer
HT Primer
1
Sys #
Sq. Ft./Unit
Applications
Precautions
600
Stonclad GS/XP, Stonshield HRI Base,
st
Stonshield SLT 1 Broacast, Stonset
st
TG4/TG5/CG5, Stontec ERF 1 Broadcast,
Below SL Primer
MUST REMAIN TACKY!!! Primer will
blush if allowed to cure. Never let
Standard Primer puddle.
909
600
Stonclad HT/HD, Stonset HG5/CG4, Stonchem
441, Stonchem 500/600 Series Applications,
Coatings Only Applications
Do not allow HT Primer to puddle.
Stonclad UR, Stonset TG6, Stonchem 441 (Cold
Applications)
MUST ADD PART C!!! Primer can
foam if Part C is left out. Overlayment
must be applied wet-on-wet.
Urethane
1
Primer
General Service Urethane
Primer
400H/
400V
300 / 150
Stonblend
1
Primer
UV Resistant Epoxy Primer
908
600
Stonblend GSI
MUST REMAIN TACKY!!!
Pinhole Filling Epoxy Primer
914
1200
Stonlux SL/AT, Stonres RTZ, Stonflex ME7
Squeegee only, DO NOT BACKROLL!!!
Must add Part C to work properly.
58080
200
Stontec UTF, Stonshield URT
Do not allow UTF Primer to puddle.
Primer can foam if allowed to puddle.
SL Primer
2
Stontec
UTF/
Stonshield
URT Primer
Primer for Urethane
Broadcast Systems
1
Xpress
Primer
General Service Acrylic
Primer
64630
200
Stonshield/Stontec XPRESS systems
Watch for primer soak-in. If any areas
dry out, they must be recoated.
XPRESS systems may not cure fully if
applied over an unprimed substrate.
Allow for good air flow. PRIMER HAS A
VERY STRONG ODOR!
Stonset
2
Primer
Stonfil OP2
3
Primer
Stonchem
800 Series
1
Primer
Thickened Bis A Epoxy
Primer
903
300
Mortar systems applied OVER Stonset TG4/TG5
MUST REMAIN TACKY!!!
Latex Based Primer
3152
1100
Exclusively for Stonfil OP2
Allow primer to dry before applying
OP2. NO PUDDLES!!!
Vinyl Ester Primer
56020
200
Stonchem 700/800 Series Applications
MUST GET EXACT COVERAGE!!!
Below any epoxy or urethane system when
substrate is contaminated
For use with epoxies, allow primer to
soak into substrate for approx. 1 hour
before overlaying. For use with
urethane primer, penetrating primer
must be allowed to cure overnight. For
all other urethanes, allow primer to set
up for 2 hours before overlaying.
Penetrating
Primer
General Service Bis F Epoxy
Primer- Better Adhesion for
Questionable Substrates
915
600
Green
Concrete
Primer
Stoncrest
GS3
3
Clear
General Service Primer for
Use over Green Concrete
Solvent Based Epoxy
Coating
916/917
600
Below many systems when moisture
transmission from Green Concrete is evident.
Consult Tech Bulletin (2/2/09)
Proper Use Dependent on System.
Consult Tech Bulletin (2/2/09) for
detailed application instructions.
6312
400
Excellent primer for metal substrates and fixtures
Allow for good air flow. Solvent in GS3
has strong odor.
ATM/ATK
1
Primer
Conductive Epoxy Primer
912/904
600
Stonlux ATM/ATK, Stonkote AT5
Conductive
Novalac
1
Primer
Conductive Epoxy Primer
905
600
Stonchem 691
YOU MUST GET EXACT COVERAGE
DURING INSTALLATION!!! Conductivity
must be tested before overlayment.
YOU MUST GET EXACT COVERAGE
DURING INSTALLATION!!! Conductivity
must be tested before overlayment.
1
Applied by the squeegee-backroll method
Applied by squeegee only method
3
Applied by the dip and roll method
2
8/09